TwoWay Thing - Dvosmjerni GSM Kontroler
Moderators: pedja089, stojke369, [eDo], trax
Ovako, da bi mobitel koristio na ovom uredjaju on u sebi mora imati embedded modem. Sa njim cemo komunicirati preko FBUS, ne MBUS!
Znaci, moras imati FBUS interface na telefonu a u njemu MODEM hardverski... Mislim da u ovim tvojim nokijama 3310 i slicno njega nazalost nema...
5110 mislim da cak ima, ali on nema FBUS??? Ja imam 5130 ovdje i sve je bilo OK dok nisam spojio i vidio da ne radi
-
- Pocetnik na forumu
- Posts: 34
- Joined: 08-08-2005, 01:28
Ja imam..
ja imam imao sam 3510 a sada 3300 sto nema veze sa uredajem.
Ali imam i 5110 sto bi nadam se moglo raditi. ??? (trebam ga kupiti i to veoma povoljno - 15 maraka!!!) pa bih te molio da pogledaš da li može i taj tel da tipu javim da li da mi ga ostavi. što prije možeš!!
I samo da te pitam, odakle si ti ako se smije znati??
Ali imam i 5110 sto bi nadam se moglo raditi. ??? (trebam ga kupiti i to veoma povoljno - 15 maraka!!!) pa bih te molio da pogledaš da li može i taj tel da tipu javim da li da mi ga ostavi. što prije možeš!!
I samo da te pitam, odakle si ti ako se smije znati??
:::: Atmel For life ::::
Ajde bit cu opet malo dosadan ali zasto ne redizanjiras FW za automatski bitrate [ znaci SW emulirano] i ne napises to za Atmel a imas i puno bolji izbor MCUa . I ja sam bio poceo s PIC 16 serijom kad su MCUi u pitanju ali cim su dosli Atmeli i vidjele se njihove karakteristike [ a pogotovo "velik" SRAM i EPROM] 1 taktni "motor" , bilo je jasno sto slijedi !!
Pozdrav
Pozdrav
- bhgsmservis
- Posts: 9
- Joined: 19-12-2005, 14:40
- Location: BiH
- Contact:
Hi Trax,
I already constructed my 3.01a on perfboard I got it working but there seems to be a problem.
I issued the command:
0.abcd
the controller replies with Ok! but when I inquire using this command:
H.
this is all I got:
Relay - A=On! B=On! C=On! D=On!
I just can't turn it off..
BTW: is it alright if I omit ALL the parts in the sensor section except for the 2 pullup resistors?
What is the function of the 5 volts Zener at MCLR to Gnd?
TIA
rhonn
Ooppss...sorry...it was already posted on this page..http://www.elektronika.ba/forum/viewtop ... c&start=90
Got it working now Trax..I just need a PCB now..I'll try to attached some pictures tomorrow..
rhonn
I already constructed my 3.01a on perfboard I got it working but there seems to be a problem.
I issued the command:
0.abcd
the controller replies with Ok! but when I inquire using this command:
H.
this is all I got:
Relay - A=On! B=On! C=On! D=On!
I just can't turn it off..
BTW: is it alright if I omit ALL the parts in the sensor section except for the 2 pullup resistors?
What is the function of the 5 volts Zener at MCLR to Gnd?
TIA
rhonn
Ooppss...sorry...it was already posted on this page..http://www.elektronika.ba/forum/viewtop ... c&start=90
Got it working now Trax..I just need a PCB now..I'll try to attached some pictures tomorrow..
rhonn
rhonnz
Hello,
Here is the new version of HEX file.
http://www.elektronika.ba/forum/uploadz ... 0_7110.rar
http://www.elektronika.ba/forum/uploadz ... _6310i.rar
The 6310i version has a known issue = The CALLing progress doesn't complete successfully. The problem is in the phone itself.
Please save current versions that you have on your PC and try this new one.
Here is the new version of HEX file.
http://www.elektronika.ba/forum/uploadz ... 0_7110.rar
http://www.elektronika.ba/forum/uploadz ... _6310i.rar
The 6310i version has a known issue = The CALLing progress doesn't complete successfully. The problem is in the phone itself.
Please save current versions that you have on your PC and try this new one.
Here among the files: http://www.elektronika.ba/projekti/?akc ... dprojekt=6
Is ENGLISH description. I think I have updated it. Also check the bosnian version for table of commands to see if anything is new...
Is ENGLISH description. I think I have updated it. Also check the bosnian version for table of commands to see if anything is new...